• Concentrated flow erosion rates reduced through biological geotextiles

      Smets, T.; Poesen, Jean; Langhans, C; Knapen, A; Fullen, Michael A. (Wiley InterScience, 2009)
      Soil erosion by concentrated flow can cause serious environmental damage. Erosion-control geotextiles have considerable potential for reducing concentrated flow erosion. However, limited data are available on the erosion-reducing potential of geotextiles. In this study, the effectiveness of three biological geotextiles in reducing soil losses during concentrated flow is investigated. Hereto, runoff was simulated in a concentrated flow flume, filled with an erodible sandy loam on three slope gradients (13·5, 27·0 and 41·5%). Treatments included three biological geotextiles (borassus, buriti and bamboo) and one bare soil surface. Darcy–Weisbach friction coefficients ranged from 0·01 to 2·84. The highest values are observed for borassus covered soil surfaces, followed by buriti, bamboo and bare soil, respectively. The friction coefficients are linearly correlated with geotextile thickness. For the specific experimental conditions of this study, borassus geotextiles reduced soil detachment rate on average to 56%, buriti geotextiles to 59% and bamboo geotextiles to 66% of the soil detachment rate for bare soil surfaces. Total flow shear stress was the hydraulic parameter best predicting soil detachment rate for bare and geotextile covered surfaces (R² = 0·75–0·84, p < 0·001, n = 12–15). The highest resistance against soil detachment was observed for the borassus covered soil surfaces, followed by buriti, bamboo and bare soil surfaces, respectively. Overall, biological geotextiles are less effective in controlling concentrated flow erosion compared with interrill erosion. Copyright © 2009 John Wiley & Sons, Ltd.
    • Dry powder inhalers: mechanistic evaluation of lactose formulations containing salbutamol sulphate.

      Kaialy, Waseem; Ticehurst, Martyn; Nokhodchi, Ali (Elsevier, 2012-02-28)
      The purpose of this study was to evaluate the relationships between physicochemical properties and aerosolisation performance of different grades of lactose. In order to get a wide range of physicochemical properties, various grades of lactose namely Flowlac 100 (FLO), Lactopress anhydrous 250 (LAC), Cellactose 80 (CEL), Tablettose 80 (TAB), and Granulac 200 (GRA) were used. The different lactose grades were carefully sieved to separate 63-90 μm particle size fractions and then characterised in terms of size, shape, density, flowability, and solid state. Formulations were prepared by blending each lactose with salbutamol sulphate (SS) at ratio of 67.5:1 (w/w), and then evaluated in terms of SS content uniformity, lactose-SS adhesion properties, and in vitro aerosolisation performance delivered from the Aerolizer. Sieved lactose grades showed similar particle size distributions (PSDs) and good flow properties but different particle shape, particle surface texture, and particle solid state. Content uniformity assessments indicated that lactose particles with rougher surface produced improved SS homogeneity within DPI formulation powders. Lactose-SS adhesion assessments indicated that lactose particles with more elongated shape and the rougher surface showed smaller adhesion force between lactose and salbutamol sulphate. Lactose powders with higher bulk density and higher tap density produced smaller emission (EM) and higher drug loss (DL) of SS. In vitro aerosolisation for various lactose grades followed the following rank order in terms of deposition performance: GRA>TAB>LAC ≈ CEL>FLO. Linear relationships were established showing that in order to maximize SS delivery to lower airway regions, lactose particles with more elongated shape, more irregular shape, and rougher surface are preferred. Therefore, considerable improvement in DPI performance can be achieved by careful selection of grade of lactose included within DPI formulations.
    • Treating mannitol in a saturated solution of mannitol: a novel approach to modify mannitol crystals for improved drug delivery to the lungs.

      Kaialy, Waseem; Nokhodchi, Ali (Elsevier, 2013-05-01)
      The aim of this study was to evaluate the influence of treatment of a promising dry powder aerosol carrier (mannitol) on the aerosolization performance of salbutamol sulphate (SS) using a novel approach: treating excess commercial carrier particles in a saturated solution of the same carrier. Commercial mannitol (CM) particles were treated with aqueous mannitol supersaturated solutions (20% and 25% w/v), under stirring, (300 rpm) for either 24h or 48 h. The results showed that particle treatment did not alter the polymorphic form of mannitol (β-mannitol); however, all treated mannitol particles demonstrated smoother surface topography and improved aerosolization performance compared to CM in dry powder inhalations. Unlike the concentration of mannitol solution used during treatment, the time of treatment to collect mannitol crystals was an essential key to modify the physical properties of mannitol and its effect on the aerosolization performance. In comparison to mannitol particles treated for 48 h, mannitol particles treated for 24h demonstrated larger size, more elongated-less regular shape, and smoother surfaces. No apparent relationship was obtained between in vitro aerosolisation behavior of SS with either mannitol particle size or shape descriptors. However, despite their larger size and more irregular-less uniformed shape, treated mannitol particles with smoother surfaces generated drug particles with smaller aerodynamic size and are expected to deliver higher amounts of drug to lower airways. The results demonstrated the potential of treating mannitol particles in aqueous solutions of the same material under controlled conditions to produce mannitol particles promising for dry powder inhaler systems. The results suggested that mannitol particle surface texture properties dominate over both particle size and particle shape of mannitol in terms of determining the aerosolization performance of mannitol.